Open access

Speed sensorless vector control of parallel-connected three-phase two-motor single-inverter drive system

Authors: R. Gunabalan, P. Sanjeevikumar [email protected], Frede Blaabjerg, Patrick W. Wheeler, Olorunfemi Ojo, and Ahmet H. ErtasAuthors Info & Affiliations

Publication: FACETS

12 April 2016

https://doi.org/10.1139/facets-2015-0004

OtherFormats

Abstract

This paper presents the characteristic behavior of direct vector control of two induction motors with sensorless speed feedback having the same rating parameters, paralleled combination, and supplied from a single current-controlled pulse-width-modulated voltage-source inverter drive. Natural observer design technique is known for its simple construction, which estimates the speed and rotor fluxes. Load torque is estimated by load torque adaptation and the average rotor flux was maintained constant by rotor flux feedback control. The technique’s convergence rate is very fast and is robust to noise and parameter uncertainty. The gain matrix is absent in the natural observer. The rotor speed is estimated from the load torque, stator current, and rotor flux. Under symmetrical load conditions, the difference in speed between two induction motors is reduced by considering the motor parameters as average and difference. Rotor flux is maintained constant by the rotor flux control scheme with feedback, and the estimation of rotor angle is carried out by the direct vector control technique. Both balanced and unbalanced load conditions are investigated for the proposed AC motor drive system. Experimental results presented in this paper show good agreement with the theoretical formulations.

Introduction

Controlling of AC motor drives in closed-loop strategy requires the speed transducers, such as tacho generators, resolvers, or digital encoders, to obtain the speed information that leads to the expensive system. In speed sensorless vector control, the speed can be estimated based on the information of line voltages and currents, and its accuracy is mostly meant for a single-inverter-driven single induction motor. In the case of practical needs such as electric traction and steel processing sectors, two or three similar rated induction motors are required with parallel operation fully controlled by a single-stage inverter drive (Bose 2001; Guzinski et al. 2009; 2010). If the machines have the same speed–torque characteristics, then speeds are equal, and torque-sharing rates are equal in all operating conditions. Practically, there will be observable differences between behaviors of machines. The speeds may not be identical because of slight difference of wheel diameters. The speed–torque characteristics that cause the different torque sharing at the same speed for slightly far from being identical machines are shown in Fig. 1 (dark blue—motor 2, green line—motor 1). If the wheel diameter of machine 1 is a bit larger than that of machine 2, then the torque sharing of machine 1 will be higher in motoring mode, but lower in braking mode, the corresponding characteristic of which is represented in Fig. 1 (blue line). In practice, both dissimilar machine characteristics and unequal wheel diameter problems exist. In these circumstances, the speed–torque behavior of both motors differs and an unbalanced condition arises (red line—motor 1, pink line—motor 2). If average currents flow through the stator windings and rotor fluxes are considered to be induced under unbalanced load conditions, then the speeds of both motors deviate much from the command speed. To reduce this speed variations, average and differential currents are used to determine the reference current.

Fig. 1.

Four induction motors controlled by a single-stage inverter drive as described by Taniguchi et al. (2006) and Kono et al. (2000), and proportional–integral (P–I) current controllers were used to generate d–q axes reference voltage signals. Simulation results of a four-motor drive system and the general equation for n number of motors connected in parallel were described by Kono et al. (2000). Additional proportional speed controllers were implemented with existing P–I controllers to improve the performance under unbalanced load conditions. In the case of multimotor drive systems, the currents flowing both average and difference through the stator as well as rotor fluxes were considered to improve the performance under unbalanced load conditions (Nishimura et al. 2007; Kawai et al. 2002; Inoue et al. 2011a, 2011b; Ruxi et al. 2006; Wei et al. 2006; Ando et al. 2004; Kouno et al. 2001; Matsuse et al. 2002; Kazuya et al. 2012; Yoshinaga et al. 2008). Most of the research papers dealt only with the hardware results for step change in speed under zero load conditions. A low-cost matrix converter with slip-frequency vector control is discussed by Yoshinaga et al. (2008), Osawa (2011a, 2011b), and Yamazaki et al. (2012). To minimize the speed difference among the induction motors under unbalanced load conditions, two-degree-of-freedom control was applied. Two more P controllers were introduced to improve the performance in addition to the P–I controllers presented in both speed control loops. In all the above literature, the estimation of speed and rotor fluxes were employed by the adaptive observers. The selection of gain matrix constant k is a tedious task by adaptive observers where the typical value of k is taken as 0.5. A new hybrid control method (speed–torque controller) projected on equalized load with power sharing between two drives for cement kiln operation is discussed by Bogiatzidis et al. (2012), Karanayil et al. (2007), and Wlas et al. (2008). Parallel-connected induction motors fed by a single-stage inverter were reviewed in Trentin et al. (2009) in light of merits and demerits of each method.

The performance of the induction motor drive is affected by motor parameters particularly at low-speed operation. In particular, the indirect field oriented vector control drive is very sensitive to rotor resistance. However, the stator resistance effect is significant in low-speed operation and by knowing its good precision value, the accurate estimation of rotor speed can be obtained. The variation of rotor resistance found to be 100% at the maximum due to rotor heating as reported by Rashed et al. (2003), Barut et al. (2007, 2008), and Bowes et al. (2004). In particular, small deviations in stator resistance, rotor resistance, and (transient and magnetizing) inductance value cause oscillations in estimated speed. Furthermore, performance deterioration can be ensured by neglecting iron loss of the induction motor model, which in turn causes errors in rotor flux, slip, and torque calculations. Neural networks, genetic algorithm, model reference adaptive system, and extended Kalman filter are used to estimate the unknown parameters accurately (Rashed et al. 2003; Barut et al. 2007, 2008; Bowes et al. 2004).

To overcome the difficulties stated above, natural observer is used to calculate the estimation of the speed, stator current, and rotor fluxes of both motors, as carried out in this paper. The direct field oriented vector control scheme is employed to calculate the flux angle. Average rotor flux derived from both induction motors is kept constant by rotor flux feedback control (Gunabalan et al. 2015, in press). Average and differential currents flowing through the stator and rotor fluxes are used to calculate the reference current. Experimental results are presented for balanced and unbalanced load environmental circumstances to prove the effectiveness of the method, as proposed.

The paper is organized as follows: “Analysis of speed estimation using observer” section discusses the concepts of natural observer, “Parallel connected two induction motor drive” section explains about necessary equations, “Experimental implementation and results” section presents the experimental results under various running conditions, and finally ends with “Conclusions” section.

Analysis of speed estimation using observer

The structure of the natural observer is similar to and as well as its characteristic is identical to the induction motor for the given input voltage and load torque condition. It should be noted that the convergence rate of the observer is faster than that of the motor in reaching the steady-state behavior. For estimating the rotor speed by natural observer, the fourth-order induction motor model in stator flux oriented reference frame is used, where stator currents and rotor fluxes are considered as state variable parameters.

Therefore, a three-phase induction motor can be represented in state space as follows:

\frac{d X}{d t} = A x + B u

(1)

Y = C x

(2)

where

A = [\begin{matrix} \frac{- 1}{T_{S}} & 0 & \frac{L_{m}}{L_{s}^{'} L_{r} τ_{r}} & \frac{ω_{r} L_{m}}{L_{s}^{'} L_{r}} \\ 0 & \frac{- 1}{T_{S}} & \frac{- ω_{r} L_{m}}{L_{s}^{'} L_{r}} & \frac{L_{m}}{L_{s}^{'} L_{r} τ_{r}} \\ \frac{L_{m}}{τ_{r}} & 0 & \frac{- 1}{τ_{r}} & {- ω}_{r} \\ 0 & \frac{L_{m}}{τ_{r}} & ω_{r} & \frac{- 1}{τ_{r}} \end{matrix}]; B = [\begin{matrix} \frac{1}{{σ L}_{S}} & 0 \\ 0 & \frac{1}{{σ L}_{S}} \\ 0 & 0 \\ 0 & 0 \end{matrix}]; C = [\begin{matrix} 1 & 0 & 0 & 0 \\ 0 & 1 & 0 & 0 \end{matrix}]

\frac{1}{T_{s}} = \frac{R_{s} + R_{r} {(L_{m} / L_{r})}^{2}}{L_{s}^{'}}; L_{s}^{'} = σ L_{s} .

where

σ = 1 - \frac{L_{m}^{2}}{L_{s} L_{r}}

, leakage coefficient;

x = {[\begin{matrix} i_{d s}^{s} & i_{q s}^{s} & φ_{d r}^{s} & φ_{q r}^{s} \end{matrix}]}^{T}

;

Y = [\begin{matrix} i_{d s}^{s} & i_{q s}^{s} \end{matrix}] = i_{s}

;

u = {[\begin{matrix} V_{d s}^{s} & V_{q s}^{s} \end{matrix}]}^{T}

;

R _s, R _r: stator and rotor self-inductance (Ω), respectively;

L _s, L _r: stator and rotor self-inductance (H), respectively;

L _m: mutual inductance (H);

ω _r: rotor time constant=L _r/R _r;

τ _r: motor angular velocity (rad/s).

Figure 2 shows the block diagram representation of the natural observer, and the system described by eqs. (1) and (2) is exactly in the same form of the induction motor model without any external feedback. Estimation of the stator currents and the rotor fluxes can be represented by the following equations:

\frac{d \hat{X}}{d t} = A \hat{x} + B u

(3)

\hat{Y} = C \hat{x}

(4)

where

A = [\begin{matrix} \frac{- 1}{T_{S}} & 0 & \frac{L_{m}}{L_{s}^{'} L_{r} τ_{r}} & \frac{{\hat{ω}}_{r} L_{m}}{L_{s}^{'} L_{r}} \\ 0 & \frac{- 1}{T_{S}} & \frac{- {\hat{ω}}_{r} L_{m}}{L_{s}^{'} L_{r}} & \frac{L_{m}}{L_{s}^{'} L_{r} τ_{r}} \\ \frac{L_{m}}{τ_{r}} & 0 & \frac{- 1}{τ_{r}} & {- \hat{ω}}_{r} \\ 0 & \frac{L_{m}}{τ_{r}} & {\hat{ω}}_{r} & \frac{- 1}{τ_{r}} \end{matrix}]; B = [\begin{matrix} \frac{1}{{σ L}_{S}} & 0 \\ 0 & \frac{1}{{σ L}_{S}} \\ 0 & 0 \\ 0 & 0 \end{matrix}]; C = [\begin{matrix} 1 & 0 & 0 & 0 \\ 0 & 1 & 0 & 0 \end{matrix}]

\hat{x} = {[\begin{matrix} {\hat{i}}_{d s}^{s} & {\hat{i}}_{q s}^{s} & {\hat{φ}}_{d r}^{s} & {\hat{φ}}_{q r}^{s} \end{matrix}]}^{T}; u = {[\begin{matrix} V_{d s}^{s} & V_{q s}^{s} \end{matrix}]}^{T}; \hat{Y} = {[\begin{matrix} {\hat{i}}_{d s}^{s} & {\hat{i}}_{q s}^{s} \end{matrix}]}^{T} = {\hat{i}}_{s}

The estimated quantities are denoted by “^”.

Fig. 2.

Load torque is estimated by the active power error because the correction term and T̂_L load torque are kept within two known limits to avoid unstable oscillations. Estimation of load torque is given by Gunabalan et al. (2015, in press):

{\hat{T}}_{L} = K_{D} e_{P} + K_{P} e_{P} + K_{I} \int e_{P} d t limiting {\hat{T}}_{L} \in (T_{\min}, T_{\max})

(5)

where

e_{P} = V_{d s}^{s} ({\hat{i}}_{d s}^{e} - i_{d s}^{e}) + V_{q s}^{s} ({\hat{i}}_{q s}^{e} - i_{q s}^{e})

(6)

Estimation of rotor speed can be obtained from the estimated stator current, rotor flux, and load torque as follows:

{\dot{\hat{ω}}}_{r} = (\frac{3}{2}) (\frac{n_{p}}{J}) (\frac{L_{m}}{L_{r}}) [{\hat{φ}}_{d r}^{s} {\hat{i}}_{q s}^{s} - {\hat{φ}}_{q r}^{s} {\hat{i}}_{d s}^{s}] - \frac{{\hat{T}}_{L}}{J}

(7)

where n_p is the number of pole pairs and J is the inertia of motor load system (kg m²).

Parallel-connected two induction motor drive

The current flowing in the parallel-connected induction motors supplied from a single-stage inverter drive is shown in Fig. 3 (Yoshinaga et al. 2008). If the current flowing in each motor is unbalanced, and if there is a slight difference between the wheel diameters or the machine parameters, this causes unbalanced load conditions where i _s1 will not be equal to i _s2. In this situation, the average current and torque can be expressed as follows:

{\bar{i}}_{s} = \frac{i_{s 1} + i_{s 2}}{2}

(8)

{\bar{T}}_{e} = \frac{T_{e 1} + T_{e 2}}{2} = T_{e}^{*}

(9)

where T ₁ and T ₂ are derived from the speed controllers.

Fig. 3.

Average current ̅i _s is compared with the reference current i*_s to generate the control voltage for the inverter. Figure 4 shows the configuration of parallel-connected induction motor drive fed by a single-stage inverter drive; main components are natural observer with adaptive load torque estimation, calculation block of reference current values, and current regulated pulse width modulated (CRPWM) voltage-source inverter. With the measured line voltage and currents, the speeds of both motors are estimated and the torque reference of each motor is calculated from the speed error using P–I controllers. Correspondingly, the space vector model of induction motor is used to derive the equations for i _ds and i _qs as follows:

V_{d s}^{e} = i_{d s}^{e} R_{s} + p φ_{d s}^{e} + j ω_{e} φ_{d s}^{e}

(10)

V_{q s}^{e} = i_{q s}^{e} R_{s} + p φ_{q s}^{e} + j ω_{e} φ_{q s}^{e}

(11)

0 = i_{d r}^{e} R_{r} + p φ_{d r}^{e} + j (ω_{e} - ω_{r}) φ_{d r}^{e}

(12)

0 = i_{q r}^{e} R_{r} + p φ_{q r}^{e} + j (ω_{e} - ω_{r}) φ_{q r}^{e}

(13)

φ_{d s}^{e} = L_{s} i_{d s}^{e} + L_{m} i_{d r}^{e}

(14)

φ_{q s}^{e} = L_{s} i_{q s}^{e} + L_{m} i_{q r}^{e}

(15)

φ_{d r}^{e} = L_{r} i_{d r}^{e} + L_{m} i_{d s}^{e}

(16)

φ_{q r}^{e} = L_{r} i_{q r}^{e} + L_{m} i_{q s}^{e}

(17)

T_{e} = \frac{3}{2} \frac{P}{2} (\frac{L_{m}}{L_{r}}) (φ_{d r}^{e} i_{q s}^{e} - φ_{q r}^{e} i_{d s}^{e})

(18)

From eq. (12),

i_{d r}^{e} = \frac{- p φ_{d r}^{e} - j (ω_{e} - ω_{r}) φ_{d r}^{e}}{R_{r}}

(19)

By substituting this expression in eq. (16), we get

φ_{d r}^{e} = L_{r} \frac{- p φ_{d r}^{e} - j (ω_{e} - ω_{r}) φ_{d r}^{e}}{R_{r}} + L_{m} i_{d s}^{e}

(20)

Further after simplification,

p φ_{d r}^{e} + {S_{r} + j (ω_{e} - ω_{r})} φ_{d r}^{e} = L_{m} S_{r} i_{d s}^{e}

(21)

p φ_{q r}^{e} + {S_{r} + j (ω_{e} - ω_{r})} φ_{q r}^{e} = L_{m} S_{r} i_{q s}^{e}

(22)

From eqs. (21) and (22), the general equation is represented as

p φ_{r}^{e} + {S_{r} + j (ω_{e} - ω_{r})} φ_{r}^{e} = U i_{s}^{e}

where

U = S_{r} L_{m}; S_{r} = \frac{R_{r}}{L_{r}}

(23)

Fig. 4.

The equations for motors 1 and 2, which is connected in parallel, are

p φ_{r 1}^{e} + {S_{r 1} + j (ω_{e} - ω_{r 1})} φ_{r 1}^{e} = U_{1} i_{s 1}^{e}

(24)

p φ_{r 2}^{e} + {S_{r 2} + j (ω_{e} - ω_{r 2})} φ_{r 2}^{e} = U_{2} i_{s 2}^{e}

(25)

respectively.

By averaging and differential averaging eqs. (24) and (25), we obtain

p {\bar{φ}}_{r}^{e} + {{\bar{S}}_{r} + (ω_{e} - {\bar{ω}}_{r})} + {Δ {\bar{S}}_{r} - Δ {\bar{ω}}_{r}} Δ {\bar{φ}}_{r}^{e} = \bar{U} {\bar{i}}_{s}^{e} + Δ \bar{U} Δ {\bar{i}}_{s}^{e}

(26)

The differential parameters between the two motors are defined as

Δ {\bar{S}}_{r} = \frac{S_{r 2} - S_{r 1}}{2}; Δ {\bar{ω}}_{r} = \frac{ω_{r 2} - ω_{r 1}}{2}; Δ \bar{U} = \frac{U_{2} - U_{1}}{2}; Δ {\bar{i}}_{s}^{e} = \frac{i_{s 2} - i_{s 1}}{2}; Δ {\bar{φ}}_{r}^{e} = \frac{φ_{r 2} - φ_{r 1}}{2}

The above equation can also be written as

p {\bar{φ}}_{r}^{e} + {{\bar{S}}_{r} + j (ω_{e} - {\bar{ω}}_{r})} + {Δ {\bar{S}}_{r} - j Δ {\bar{ω}}_{r}} Δ {\bar{φ}}_{r}^{e} = \bar{U} {\bar{i}}_{s}^{e} + Δ \bar{U} Δ {\bar{i}}_{s}^{e}

(27)

and by separating the real from imaginary part,

p {\bar{φ}}_{d r}^{e} + {\bar{S}}_{r} φ_{d r}^{e} - (ω_{e} - {\bar{ω}}_{r}) {\bar{φ}}_{q r}^{e} + Δ {\bar{S}}_{r} Δ {\bar{φ}}_{d r}^{e} + Δ {\bar{ω}}_{r} Δ {\bar{φ}}_{q r}^{e} = \bar{U} {\bar{i}}_{d s}^{e} + Δ \bar{U} Δ {\bar{i}}_{d s}^{e}

(28)

For constant flux,

p {\bar{φ}}_{d r}^{e} = 0 {\bar{φ}}_{q r}^{e} = 0 {\bar{i}}_{q s}^{e} = 0

After simplification, we have

{\bar{i}}_{d s}^{e *} = \frac{{\bar{S}}_{r} {\bar{φ}}_{d r}^{e} + Δ {\bar{ω}}_{r} Δ {\bar{φ}}_{q r}^{e} + Δ {\bar{S}}_{r} Δ {\bar{φ}}_{d r}^{e} - Δ \bar{U} Δ {\bar{i}}_{d s}^{e}}{\bar{U}}

(29)

When the stator current, rotor flux, and speed are estimated using the observer, eq. (29) is represented as

{\bar{i}}_{d s}^{e *} = \frac{{\bar{S}}_{r} {\bar{φ}}_{d r}^{e *} + Δ {\bar{\hat{ω}}}_{r} Δ {\bar{\hat{φ}}}_{q r}^{e} + Δ {\bar{S}}_{r} Δ {\bar{\hat{φ}}}_{d r}^{e} - Δ \bar{U} Δ {\bar{\hat{i}}}_{d s}^{e}}{\bar{U}}

(30)

Torque equations for motors 1 and 2 are as follows:

T_{e 1} = \frac{p L_{m 1}}{L_{r 1}} (i_{s 1}^{e} \times φ_{r 1}^{e})

(31)

T_{e 2} = \frac{p L_{m 2}}{L_{r 2}} (i_{s 2}^{e} \times φ_{r 2}^{e})

(32)

By averaging and differential averaging eqs. (31) and (32),

{\bar{T}}^{*} = p {\bar{M}}^{'} ({\bar{i}}_{s}^{e} \times {\bar{φ}}_{r}^{e} + Δ {\bar{i}}_{s}^{e} \times Δ {\bar{φ}}_{r}^{e})

(33)

{\bar{T}}^{*} = p {\bar{M}}^{'} ({\bar{i}}_{d s}^{e} {\bar{φ}}_{q r}^{e} - {\bar{i}}_{q s}^{e} {\bar{φ}}_{d r}^{e} + Δ {\bar{i}}_{d s}^{e} Δ {\bar{φ}}_{q r}^{e} - Δ {\bar{i}}_{q s}^{e} Δ {\bar{φ}}_{d r}^{e})

(34)

{\bar{i}}_{q s}^{e}

controls the average torque and

{\bar{i}}_{d s}^{e}

is zero.

\frac{{\bar{T}}^{*}}{p {\bar{M}}^{'}} = {\bar{i}}_{q s}^{e} {\bar{φ}}_{d r}^{e} + Δ {\bar{i}}_{d s}^{e} \times Δ {\bar{φ}}_{q r}^{e} - Δ {\bar{i}}_{q s}^{e} \times Δ {\bar{φ}}_{d r}^{e}

(35)

{\bar{i}}_{q s}^{e *} = \frac{\frac{{\bar{T}}^{*}}{p {\bar{M}}^{'}} - Δ {\bar{i}}_{q s}^{e} \times Δ {\bar{φ}}_{d r}^{e} + Δ {\bar{i}}_{d s}^{e} \times Δ {\bar{φ}}_{q r}^{e}}{{\bar{φ}}_{d r}^{e *}}

(36)

When the stator current and the rotor flux are estimated using the observer, eq. (36) is represented as

{\bar{i}}_{q s}^{e *} = \frac{\frac{{\bar{T}}^{*}}{p {\bar{M}}^{'}} - Δ {\bar{\hat{i}}}_{d s}^{e} \times Δ {\bar{\hat{φ}}}_{d r}^{e} + Δ {\bar{\hat{i}}}_{q s}^{e} \times Δ {\bar{\hat{φ}}}_{q r}^{e}}{{\bar{\hat{φ}}}_{d r}^{e *}}

(37)

{\bar{T}}^{*} = \frac{{\bar{T}}_{e} - (\frac{Δ {\bar{M}}^{'}}{{\bar{M}}^{'}}) Δ {\bar{T}}_{e}}{1 - (\frac{Δ {\bar{M}}^{'}}{{\bar{M}}^{'}})^{2}}

(38)

where

U = S_{r} L_{m} \bar{U} = \frac{U_{1} + U_{2}}{2} Δ \bar{U} = \frac{U_{2} - U_{1}}{2}

{\bar{M}}^{'} = \frac{1}{2} (\frac{L_{m 1}}{L_{r 1}} + \frac{L_{m 2}}{L_{r 2}}) Δ {\bar{M}}^{'} = \frac{1}{2} (\frac{L_{m 2}}{L_{r 2}} - \frac{L_{m 1}}{L_{r 1}})

{\bar{i}}_{s}^{e} = \frac{i_{s 1}^{e} + i_{s 2}^{e}}{2} Δ {\bar{i}}_{s}^{e} = \frac{i_{s 2}^{e} - i_{s 1}^{e}}{2}

{\bar{\hat{ω}}}_{r} = \frac{{\hat{ω}}_{r 1} + {\hat{ω}}_{r 2}}{2} Δ {\bar{\hat{ω}}}_{r} = \frac{{\hat{ω}}_{r 2} - {\hat{ω}}_{r 1}}{2}

{\bar{S}}_{r} = \frac{S_{r 1} + S_{r 2}}{2} Δ {\bar{S}}_{r} = \frac{S_{r 2} - S_{r 1}}{2}

L _r1, L _r2: rotor self-inductance of motors 1 and 2, respectively (H);

L _m1, L _m2: mutual inductance of motors 1 and 2, respectively (H);

ω _r1, ω _r2: angular velocity of motors 1 and 2, respectively (rad/s).

Experimental implementation and results

Two identical three-phase squirrel cage induction motors rated at 745.6 W (1 HP) are used for parallel-connected configuration (Gunabalan et al. 2015, in press). Table 1 shows the rating and parameters of the induction motor used for experimental task. The direct field oriented sensorless vector control scheme is used and the rotor angle is calculated from the estimated rotor fluxes. The complete experimental prototype set up is shown in Fig. 5. To estimate the speeds and rotor fluxes of induction motors, AD5024 bipolar analog to digital converter with 12-bit resolution measures the currents and voltages. The measured signals are processed in the TMS320F2812 digital signal processor (DSP) to estimate the speed, rotor fluxes, and stator currents.

Table 1.

Table 1. Main parameters of parallel-connected two induction motor drive.

Rated output power	745.6 W
Number of poles	4
Rated speed	1415 rpm
Rated voltage	415 V
Rated current	1.8 A
Stator resistance (R_s )	19.355 Ω
Rotor resistance (R_r )	8.43 Ω
Stator inductance (L_s )	0.715 H
Rotor inductance (L_r )	0.715 H
Mutual inductance (L_m )	0.689 H

Fig. 5.

Balanced load conditions

Initially, the reference speed is set at 1000 rpm (70% of rated speed) under no-load conditions and both motors follow the reference speed. After a particular time interval, a load of 4 Nm (80% of full-load torque) is applied to both induction motors. Figure 6a illustrates the estimated speed waveform obtained by the experimental set up, which verifies that both motors follow the speed command. The estimated torque waveform is shown in Fig. 6b. It follows the actual load torque representing that the system is stable under balanced load conditions. Phase A stator currents of motors 1 and 2 are depicted in Fig. 6c, which follows the torque demand and further confirms the balanced condition of the system.

Fig. 6.

Unbalanced load conditions

An unbalanced load condition arises, in particular, whenever there is a slight dissimilarity in wheel diameter. To illustrate such conditions in the experimental set up, unequal load is applied to both motors. Both induction motors run at a constant speed of 1000 rpm under no-load conditions initially. Now, motor 2 is loaded with 4 Nm keeping motor 1 at still no-load condition. The estimated speed response obtained under these circumstances is depicted in Fig. 7a. It is indicated that the estimated speed follows the speed set command and deviation occurs when motor 2 is loaded; again it backs to the set value by the PI regulator action. The estimated torque responses of motors 1 and 2 are shown in Fig. 7b and phase A stator currents of motors 1 and 2 are given in Fig. 7c. Stator currents confirm the unbalanced running condition, as the phase current of motor 2 is higher than that of motor 1, when motor 2 is loaded.

Fig. 7.

Furthermore, the unbalanced condition is verified by setting motor 1 loaded and motor 2 always unloaded. Correspondingly, the estimated speed response is depicted in Fig. 8a, torque response of motor 1 and motor 2 is shown in Fig. 7b, and phase A stator current of motors 1 and 2 is illustrated in Fig. 7c.

Fig. 8.

Conclusions

In this paper, the natural observer with load torque adaption technique was presented, in particular to estimate the speed and load torque of motors connected in parallel and fed by a single-stage inverter drive. The structure of the natural observer was simple. An algorithm based on direct vector control in the stationary reference frame was developed, including the natural observer for parameter estimations. The proposed algorithm has been implemented completely using the TMS320F2812 DSP with standard equal rating induction motors. The experimental results for the parallel-connected induction motor drive were demonstrated in literatures only for step change in speed at no load. In this work, experimental results have been provided for multistep change in speed, under balanced load and unbalanced load conditions to prove the effectiveness of the proposed direct vector control with the natural observer adaptation technique. The results shown in this paper always confirm the theoretical hypothesis.

References

Ando I, Sato M, Sazawa M, and Ohishi K. 2004. High efficient parallel connected induction motor speed control with unbalanced load condition using one inverter. In Proceedings of the 29th Annual Conference of the IEEE Industrial Electronics Society, IECON’04, Busan, South Korea, 2–6 November 2004, Vol. 2, pp. 1361–1366.

LOGIN TO YOUR ACCOUNT

Create a new account

Request Username

Change Password

Your password must have 8 characters or more and contain 3 of the following:

Password Changed Successfully

Verify Phone

Congrats!

Abstract

Introduction

Analysis of speed estimation using observer

Parallel-connected two induction motor drive

Experimental implementation and results

Balanced load conditions

Unbalanced load conditions

Conclusions

References

Information

Published In

History

Copyright

Data Availability Statement

Key Words

Sections

Subjects

Authors

Affiliations

Author Contributions

Competing Interests

Metrics

Other Metrics

Citations

Cite As

Export Citations

Cited by

View options

PDF

Media

Other

Share

Share the article link

Share on social media